Author |
Topic: Teves ABS Controller (Read 5239 times) |
|
workshopboy
Newbie
98 2.3 Ultima Estate Facelift
Posts: 46
|
|
Teves ABS Controller
« on: Oct 8th, 2008, 7:15pm » |
Quote Modify
|
Hi All Just a short note to let you all know that I have had the same problem with the soldered pins in the ABS controller. A little bit of work with the iron has the system working as it should once more. Many Thanks for all the advice on here Andy
|
|
IP Logged |
" You can't close what you haven't opened."
|
|
|
Cosray
Full Member
8th Scorpio, 2nd Cosworth: currently '95
Posts: 569
|
|
Re: Teves ABS Controller
« Reply #1 on: Dec 5th, 2008, 3:26pm » |
Quote Modify
|
Hi, how does one get to the controller? In my Scorpio Cosworth 95 it sits locked under the ABS Pump motor attached to a bunch of hydraulic pipes... or is that where it is? Curious, Ray
|
|
IP Logged |
|
|
|
Tompion
Administrator
1997 2.3 Ultima estate.
Posts: 2918
|
|
Re: Teves ABS Controller
« Reply #2 on: Dec 5th, 2008, 5:46pm » |
Quote Modify
|
It's under the valve block - the pump motor plugs into it. It can be taken out without undoing the hydraulic pipes apparently - not done it myself.
|
|
IP Logged |
ABS multiplug wheel sensor pins MK IV or MK 20
|
|
|
Scorpio_Mike
Senior Member
Jeep Grand Cherokee 3.0 V6 & 2.8 Sierra XR4i 4x4
Posts: 2354
|
|
Re: Teves ABS Controller
« Reply #3 on: Dec 5th, 2008, 5:56pm » |
Quote Modify
|
on Dec 5th, 2008, 5:46pm, Tompion wrote:It's under the valve block - the pump motor plugs into it. It can be taken out without undoing the hydraulic pipes apparently - not done it myself. |
| Simmo knows how to do this Over to you Mike
|
|
IP Logged |
Star sign is Scorpio ! Sierra XR4i's are great...especially when fitted with 4WD
|
|
|
Simmo
Administrator
I'm an OAP !
Posts: 5508
|
|
Re: Teves ABS Controller
« Reply #4 on: Dec 5th, 2008, 7:38pm » |
Quote Modify
|
The motor and pipework sit in a metal frame secured by three bolts which are easily undone. There is also a large multiplug connector which needs to be removed. This has a LONG bolt which needs to be fully undone and in fact pulls the connector out as it comes. There is a theory that you can then lift the motor and pipework enough to get at the two screws underneath which hold the controller to the motor etc. Personally I could not do that. The metal carrier is secured on the wheel arch by three captive bolts and the nuts are underneath. They are accessed by removing the wheel arch liner. Once the carrier is out of the way you still need a very shallow ratchet and bit to release the screws which hold the controller to the motor. There is also the two pin connector for the motor which needs to be released. If you removed the hydraulic pipes of course life would be simple as the complete unit would lift off the carrier without getting under the wheel arch. IF the problem is with the pins a scan will say that the pump is not working. The simple way to check this is to remove the two pin connector put a 12v supply to the motor and if it runs then clearly it is NOT faulty but simply not getting power ...ie: pins probably need soldering as documented by Tompion and indeed he has now mended several.....including mine!. The details are all provided,with pictures, HERE. Tompions article is Here. He has now refined the method and just cuts a hole above the pins, which sit below the connector, and thus has only a small aperture to re-seal.
|
|
IP Logged |
Now I'm an OAP
|
|
|
gozz
Senior Member
Been around awhile
Posts: 3475
|
|
Re: Teves ABS Controller
« Reply #5 on: Dec 5th, 2008, 9:28pm » |
Quote Modify
|
Cosray. Simmo's got hands like shovels If you swing the coolant header tank out of the way,undo the three fixings on the pump unit,then possibly remove a pipe clamp or two and take out the multiplug and motor plug,you can bend the unit up enough to get a short screwdriver or small ratchet bit to the two screws holding the module on. GOZZ.
|
|
IP Logged |
|
|
|
Simmo
Administrator
I'm an OAP !
Posts: 5508
|
|
Re: Teves ABS Controller
« Reply #6 on: Dec 6th, 2008, 6:47am » |
Quote Modify
|
All I can say is I tried that method but no way could I get access to the underside. One day I'm going to watch Gozz do this !!. . If you can do it good luck.
|
|
IP Logged |
Now I'm an OAP
|
|
|
workshopboy
Newbie
98 2.3 Ultima Estate Facelift
Posts: 46
|
|
Re: Teves ABS Controller
« Reply #7 on: Dec 7th, 2008, 7:56pm » |
Quote Modify
|
Hi Guys I managed to remove just the control box by undoing the torx bolts and removing just the box. i soldered the joints once I managed to open the unit and put it all back together in less than an hour
|
|
IP Logged |
" You can't close what you haven't opened."
|
|
|
Tompion
Administrator
1997 2.3 Ultima estate.
Posts: 2918
|
|
Re: Teves ABS Controller
« Reply #8 on: Dec 7th, 2008, 9:31pm » |
Quote Modify
|
As Simmo says I have looked at his MKIV ABS controller & it had the same fault as the later type of unit shown on the website. I intend to post something more about it when I’ve had a chance to test it. But for the time being here’s a couple of pictures. You need to be careful as the board isn’t far below the cover. I bored a 20mm hole directly opposite to the socket for the motor plug - on the other side of the case. As with my unit it looked OK until I scraped away the shiny mastic when the faulty joints could easily be seen. One of the motor pins connects to earth so you can test that on the car although of course it may test OK even if the solder joint is bad.
|
|
IP Logged |
ABS multiplug wheel sensor pins MK IV or MK 20
|
|
|
Tekno
Full Member
Tenho Ruohoranta
Posts: 599
|
|
Re: Teves ABS Controller
« Reply #9 on: Feb 2nd, 2010, 10:45am » |
Quote Modify
|
Hello, some folks seem to have successfully detached box only, without going under car and without detaching hydraulic pipes. Am I right? If that's correct, were the box like this, and three bolts you unbolted, those big torxes shown on this picture below? Any help appriciated, please.
|
|
IP Logged |
1998 Ford Scorpio Ultima Estate 2.3i 16V
|
|
|
Tekno
Full Member
Tenho Ruohoranta
Posts: 599
|
|
Re: Teves ABS Controller
« Reply #10 on: Feb 2nd, 2010, 2:04pm » |
Quote Modify
|
I took a risk and bended hydraulic hoses and now abs box is on my desk. How to measure it ? or shall I just cut a hole
|
|
IP Logged |
1998 Ford Scorpio Ultima Estate 2.3i 16V
|
|
|
Tekno
Full Member
Tenho Ruohoranta
Posts: 599
|
|
Re: Teves ABS Controller
« Reply #11 on: Feb 2nd, 2010, 6:14pm » |
Quote Modify
|
Well, I did cut a hole and measured pins continuity. There was no problems. Now, ideas? Should I put everything back together
|
|
IP Logged |
1998 Ford Scorpio Ultima Estate 2.3i 16V
|
|
|
Tekno
Full Member
Tenho Ruohoranta
Posts: 599
|
|
Re: Teves ABS Controller
« Reply #12 on: Feb 3rd, 2010, 12:41pm » |
Quote Modify
|
UPDATE: After scraping shiny mastic, I soldered those and then cleaned every pin of connectors. There was little bit vaseline on some pins . Then I assembled everything back together and took a ride.. and... YEAAAAAAAAAAAAAAAAAAAAAAAAAAAAAHHHHHHHHHHH IT WORKS BOTH, ABS AND TCS WORKS NOW!
|
|
IP Logged |
1998 Ford Scorpio Ultima Estate 2.3i 16V
|
|
|
PJDavis
Senior Member
2 x 1995 Jag X300 3.2 / 4.0 (Henley) 1957 XK140
Posts: 1474
|
|
Re: Teves ABS Controller
« Reply #13 on: Feb 3rd, 2010, 9:41pm » |
Quote Modify
|
My controller is the bigger looking one that is more square, is that an early or late one?
|
|
IP Logged |
I love 'Movvy' 1995 Jaguar XJ6 X300 3.2 (Henley) 1995 Jaguar XJ6 X330 4.0 (Dopey) 1957 Jaguar XK140 USA (converted to RHD, and to have fitted Mk10 420G Engine with BW 65 Auto Trans)
|
|
|
gozz
Senior Member
Been around awhile
Posts: 3475
|
|
Re: Teves ABS Controller
« Reply #14 on: Feb 3rd, 2010, 10:16pm » |
Quote Modify
|
PJD. The later one has the unit on the front held on by four screws,the early one has the unit right underneath and is more difficult to remove even though it only has two screws. GOZZ.
|
|
IP Logged |
|
|
|
PJDavis
Senior Member
2 x 1995 Jag X300 3.2 / 4.0 (Henley) 1957 XK140
Posts: 1474
|
|
Re: Teves ABS Controller
« Reply #15 on: Feb 4th, 2010, 10:04am » |
Quote Modify
|
So, is the one pictured above the early type?
|
|
IP Logged |
I love 'Movvy' 1995 Jaguar XJ6 X300 3.2 (Henley) 1995 Jaguar XJ6 X330 4.0 (Dopey) 1957 Jaguar XK140 USA (converted to RHD, and to have fitted Mk10 420G Engine with BW 65 Auto Trans)
|
|
|
gozz
Senior Member
Been around awhile
Posts: 3475
|
|
Re: Teves ABS Controller
« Reply #16 on: Feb 4th, 2010, 10:22am » |
Quote Modify
|
Yes,the box shown by Tekno has traction control,Tompion's hasn't,but they are the early type.I have an idea,though I may be wrong,that all TC equipped cars used the early type. GOZZ.
|
|
IP Logged |
|
|
|
blue2
Newbie
1995 Cosworth 24v & 2008 Mondeo Estate
Posts: 8
|
|
Re: Teves ABS Controller
« Reply #17 on: Mar 13th, 2011, 7:18pm » |
Quote Modify
|
Just to say thanks to the guys who gave advice about using Alex Peper's Tricom lead for diagnosing ABS problems, I had stuggled getting any code until I read the tips. I had an intermiitent problem with the ABS/TCS lights coming on at 1 5 Mph, as it happened the problem dissapeard for a month around the time of the MOT but returned last week! Mine is the MkIV larger type by the way. Using the Trican lead I found as suspected the now common Pump Motor control circuit code. Before proving the point I had aquired a spare unit very cheaply on Ebay, so I have installed just the Electronic module which I managed to do without disconnecting any hydraulics. All works OK, as most of you will know an initial run at over 15Mph was required to get rid of the ABS/TCS lights (one complete test cycle I assume). I have now dissected the original module - I boldly hacked the top of by going around with a small hobby type diamond wheel as all other efforts failed and seeing the amount of sealant I can now see why! I would agree that the hole method is easier as there is very little else one could repair in there (and I am an ex computer engineer). I have now resoldered the pump pins and will reseal with mastic whilst finding some way of reinstating the shielding provided by the silvered box cover. I have some photos showing the complete insides if anyone is interested. Will just keep as a spare unit which I will now probably never need as the car is already 16 years old.
|
|
IP Logged |
|
|
|
|