Author |
Topic: NEW MAF ? (Read 1153 times) |
|
dan_the_man
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 314
|
howdy folks, a little advice please. my old cossie has done 180,000 miles and still drives great. I have noticed though it takes about a second and a half to engage D or R. also at low and moderate speeds the clutch seems to slip and she Rev's, and clunks into gear. the MAF has been cleaned 3 times with little or no improvement. I have done a little reading on the site and I would guess this is my problem . I am sure P0174 Bank 2 Fuel System too Lean (V6 models only) and P0175 Bank 2 Fuel System too Rich (V6 models only) both came up . what could I expect to pay for a MAF ? The gearbox oil is fine. Many thanks, Dan.
|
|
IP Logged |
|
|
|
martin_rowe
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/homer.gif) I love YaBB 1G - SP1!
Posts: 879
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #1 on: Jan 10th, 2008, 8:51am » |
Quote Modify
|
from memory for a 24v about £275 for new from ford, bosch were doing some recons at about £150 last time I checked.
|
|
IP Logged |
Rally Drivers Do It Sideways
|
|
|
Simmo
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm an OAP !
Posts: 5508
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #2 on: Jan 10th, 2008, 9:40am » |
Quote Modify
|
Dan, could you not borrow one and swap it over before going down the replacement route?, particularly at that price !. Just found THIS on E-Bay but their details are on the site. The code number shown may not relate to the Cosworth MAF but worth a call I would suggest.
|
|
IP Logged |
Now I'm an OAP
|
|
|
scorpio_man
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://img.photobucket.com/albums/v521/scorpio_man/scotland_royal_banner_fl_md_clr.gif)
Ford Kuga awd
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 5654
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #3 on: Jan 10th, 2008, 12:54pm » |
Quote Modify
|
hi there you need to make sure it's for the 24v as it's bigger and bolts on. the 16v version uses clips. hth btw, the ebay one looks to be for a 16v engine.
|
|
IP Logged |
|
|
|
martin_rowe
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/homer.gif) I love YaBB 1G - SP1!
Posts: 879
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #4 on: Jan 10th, 2008, 1:24pm » |
Quote Modify
|
unfortunatly, as with most things on a 24v, they asre 1 offs.
|
|
IP Logged |
Rally Drivers Do It Sideways
|
|
|
Simmo
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm an OAP !
Posts: 5508
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #5 on: Jan 10th, 2008, 1:31pm » |
Quote Modify
|
on Jan 10th, 2008, 12:54pm, scorpio_man wrote:hi there you need to make sure it's for the 24v as it's bigger and bolts on. the 16v version uses clips. hth btw, the ebay one looks to be for a 16v engine. |
| That would seem to be the case Andrew as that number is on one that I have.
|
|
IP Logged |
Now I'm an OAP
|
|
|
dan_the_man
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 314
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #6 on: Jan 10th, 2008, 6:24pm » |
Quote Modify
|
many thanks Guys, does anyone know what the FINIS CODE is for the 24v MAF ?
|
|
IP Logged |
|
|
|
Jonnycab
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://i70.photobucket.com/albums/i101/jonnycab/JP_nitrous.gif)
Former owner of 2.3 Ultima Facelift saloon
Posts: 3900
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #7 on: Jan 11th, 2008, 1:54am » |
Quote Modify
|
Are you sure it's the MAF that is causing the problem ? The fault codes could indicate a faulty fuel pressure regulator, & be totally unrelated to the autobox problem that you have Could be the autobox solenoid is faulty ?
|
|
IP Logged |
|
|
|
dan_the_man
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 314
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #8 on: Jan 11th, 2008, 4:43pm » |
Quote Modify
|
I am not sure. Jc you could be bang on ! I just thought I would try the MAF . don't know why.
|
|
IP Logged |
|
|
|
pedropedro
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif)
Posts: 677
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #9 on: Jan 11th, 2008, 7:09pm » |
Quote Modify
|
its fairly easy to check the MAF assuming you have the obd vehicle explorer software from alex pepper..worth getting at idle you should expect to see around .6-.8 volts rising up to around 2 volts at 2000 rpm approx then it takes the guesswork out it...just a thought...john
|
|
IP Logged |
|
|
|
TiberiuS
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://i61.tinypic.com/29w0f81.jpg)
Ex. 1996 2.3 Ultima - RIP P789 KHJ
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 2257
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #10 on: Jan 11th, 2008, 9:04pm » |
Quote Modify
|
If you pull the MAF, it should go into limp-home mode and revert to default values, if that doesn't improve/change the shifting problem, you can be pretty sure the MAF isn't the cause. Exactly the symptoms I used to get with my autobox, 180k is a lot if it's on the original one Regards, Bruce.
|
|
IP Logged |
Bruce - '07 Jaguar XKR coupe, '95 Jaguar XJ Sport 4.0, '82 Ford Capri 2.0 Ghia, '15 Honda Civic (sloooooww..)
|
|
|
dan_the_man
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 314
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #11 on: Jan 12th, 2008, 5:23pm » |
Quote Modify
|
CHEERS AGAIN FOLKS, I unplugged the MAF , took her for a spin and the change was noticably more 'clunky'. when I plugged it back in and did the same run again it felt more smooth than before !
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://img.photobucket.com/albums/v521/scorpio_man/scotland_royal_banner_fl_md_clr.gif)
Ford Kuga awd
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 5654
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #12 on: Jan 12th, 2008, 7:51pm » |
Quote Modify
|
hi dan the codes i got from your car at the last harewood housee meeting were... p051 p1131 p1132 did you get another scan done? regards
|
|
IP Logged |
|
|
|
pete from Hull
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/boyandmower.gif) Non Scorpio at the moment, but still interested...
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 1365
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #13 on: Jan 13th, 2008, 9:23am » |
Quote Modify
|
on Jan 10th, 2008, 6:24pm, dan_the_man wrote:many thanks Guys, does anyone know what the FINIS CODE is for the 24v MAF ? |
| Hi Dan just fond this on ebay Item No 320206637992 Don't know if it's any good to you.... Pete
|
|
IP Logged |
Bring back fair wages.........
|
|
|
Dave2302
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/winnie.gif) 2006 Mercedes S55 AMG, Retired Barefoot Waterskier
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 1119
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #14 on: Jan 13th, 2008, 3:22pm » |
Quote Modify
|
Hi If you get a 16v MAF or a 2.0 Mondeo you will find you can undo the tamper proof torx screws and fit it into the housing of the cossie one. Its the guts bit that goes wrong not the housing, I beleive this applies to any of the Ford MAF's with the same plug / bolt pattern. Did this to mine, runs and drives lovely and got rid of a few gremlins. Regards Dave.
|
|
IP Logged |
Dave "The 'ol Bear" ex Footer !
|
|
|
Tompion
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://i.imgur.com/YwLOTZk.jpg)
1997 2.3 Ultima estate.
Posts: 2918
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #15 on: Jan 13th, 2008, 3:34pm » |
Quote Modify
|
I have a MAF off a 2.9 but it's a different plug to the one on my 2.3 - don't know if the plug varied over the years.
|
|
IP Logged |
ABS multiplug wheel sensor pins MK IV or MK 20
|
|
|
dan_the_man
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 314
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #16 on: Jan 16th, 2008, 2:33pm » |
Quote Modify
|
Cheers filks. I have and are having some comp dramaz ! I have had another scan done, Lost the codes. will get another tomorrow. I'll let you know how I go. CHEERS.
|
|
IP Logged |
|
|
|
Highlander
Moderator Expert
![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif)
![](http://i1001.photobucket.com/albums/af132/CharlieSloan/Flags/Scotland.gif)
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 8244
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: NEW MAF ?
« Reply #17 on: Jan 16th, 2008, 5:27pm » |
Quote Modify
|
on Jan 13th, 2008, 3:34pm, Tompion wrote:I have a MAF off a 2.9 but it's a different plug to the one on my 2.3 - don't know if the plug varied over the years. |
| Different MAF's they are not interchangeable
|
|
IP Logged |
![](http://i8.tinypic.com/2qvxssl.gif)
on Oct 17th, 2011, 12:35pm, Simmo wrote:I give up ! Too much for an old boy! |
|
|
|
|
|