Author |
Topic: Lambda sensors (Read 1388 times) |
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Lambda sensors
« on: Dec 6th, 2008, 3:58pm » |
Quote Modify
|
Hi, My scorpio failed the emission test, it has CO 0.7, and HC 280 ppm on idle, and HC 80 ppm on revs, so I suspect the lambda sensors are due for replacement. Since the 24V has potentially four failing sensors, and replacing all att once is quite expensive, will a failing rear sensor have any affect on the emissions?
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://img.photobucket.com/albums/v521/scorpio_man/scotland_royal_banner_fl_md_clr.gif)
Ford Kuga awd
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 5654
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #1 on: Dec 6th, 2008, 4:25pm » |
Quote Modify
|
hi there no, the rear sensors are just cat monitors. hth
|
|
IP Logged |
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #2 on: Dec 6th, 2008, 6:25pm » |
Quote Modify
|
on Dec 6th, 2008, 4:25pm, scorpio_man wrote:hi there no, the rear sensors are just cat monitors. hth |
| Sounds good then, I'm a bit on a budget, the Finnish customs just billed me on 880 euros for registration tax (based on a hypothetical value of 3800 euros the customs assumes it has, ridiculous system), have only a week to fix it until the temp plates expire. Will keep my fingers crossed it isn't the cats. I'll have the values checked in any case, but I can replace the rear ones with less hurry should they have failed as well. Cleaned the MAF, but it had no effect on the emissions, but the car felt more responsive, so definitely worth the trouble. Otherwise, no serious issues except the rh headlight leveller didn't work.
|
|
IP Logged |
|
|
|
martin_rowe
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/homer.gif) I love YaBB 1G - SP1!
Posts: 879
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #3 on: Dec 7th, 2008, 11:39am » |
Quote Modify
|
what was your Llambda vaue on the emission test, if it was close to 1.000 (higher than 1.000 is lean mixture, lower than 1.000 is rich mixture, with or without a cat fitted) then emissions are ok, probably a cat problem, more info needed. rear sensors are just for monitoring purposes, its the front ones that control emissions (together with many other sensors.
|
|
IP Logged |
Rally Drivers Do It Sideways
|
|
|
Highlander
Moderator Expert
![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif)
![](http://i1001.photobucket.com/albums/af132/CharlieSloan/Flags/Scotland.gif)
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 8244
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #4 on: Dec 7th, 2008, 11:49am » |
Quote Modify
|
on Dec 6th, 2008, 6:25pm, tlundkvi wrote: Otherwise, no serious issues except the rh headlight leveller didn't work. |
| Got a spare leveller unit if you need one
|
|
IP Logged |
![](http://i8.tinypic.com/2qvxssl.gif)
on Oct 17th, 2011, 12:35pm, Simmo wrote:I give up ! Too much for an old boy! |
|
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #5 on: Dec 7th, 2008, 6:00pm » |
Quote Modify
|
on Dec 7th, 2008, 11:49am, Highlander wrote: Got a spare leveller unit if you need one |
| Good to know, thanks, will have to take the car to a garage to get the emissions tested and (likely) to replace the sensors, we'll check at the same time the leveller. Highlander, if the "stopper thingies" inside the road springs have nothing to do with self levelling, would you have an extra pair of those as well? I will put the picture of how it looks when I take it to a garage, but the failed MOT for registration has kept me occupied (mentally at least). The lamdba value was not printed on the certificate, cleaning the MAF changed the CO to 0,9 (0,5 allowed) and the HC to 325 (100 allowed) on idle when tested in a garage. AFAIK a dirty MAF causes a too lean mixture. The last german MOT was made in march this year, but the test values are not available anymore. The values would have been useful, to see if a sudden drop has occurred.
|
|
IP Logged |
|
|
|
Highlander
Moderator Expert
![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/starmod.gif)
![](http://i1001.photobucket.com/albums/af132/CharlieSloan/Flags/Scotland.gif)
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 8244
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #6 on: Dec 7th, 2008, 6:45pm » |
Quote Modify
|
The rubber things? no sorry, they seem to perish fairly badly, rarely see a good one
|
|
IP Logged |
![](http://i8.tinypic.com/2qvxssl.gif)
on Oct 17th, 2011, 12:35pm, Simmo wrote:I give up ! Too much for an old boy! |
|
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #7 on: Dec 8th, 2008, 2:41pm » |
Quote Modify
|
Small update, the garage I visited (friends) didn't have any advanced ODB scanning equipment, so testing the values of the sensors was not possible. We added the "normal" Forte treatment, ran it in first gear at 6krpm for 30 minutes, effect CO dropped to 0,6 and HC to 180 on idle. Lambda value 1,01-1,03 during the test. On revs, CO was unchanged but HC dropped to 60 at best. Funny observation was that when running idle, we pulled the MAF plug out, but it didn't change the emissions remarkably, neither did the engine stop or warning lights come on. But spraying CRC-MAF on it while running affected engine sound, the idle revs fell to around 400-500 for a few secs. Have a bottle of special Forte Fuel System Cleaner to run through, and after that the ODB specialist will test all sensors if the emission test still fails. Both garages doubted cat failure, they both believed the cats should rattle and warning lights come on if this was the case + the emissions should be a lot worse.
|
|
IP Logged |
|
|
|
martin_rowe
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/homer.gif) I love YaBB 1G - SP1!
Posts: 879
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #8 on: Dec 8th, 2008, 5:02pm » |
Quote Modify
|
Unfortunatly Llambda value of 1.01 - 1.03 means emissions are correct, (Llambda value will not change if the cat is good or bad) with that Llambda reading, but still high CO means the cats are not 'burning' off the CO and HC's, they only rattle when the 'brick' breaks up, how long have you owned the car ?, the catsare expensive, many people remove the 'brick'. sorry, with out further data looks like a cat problem, try comparing Llambda sensor readings (electrical) of pre & post cat sensors, a post cat sensor with a fluctuating reading (between 0.2 -0.8v) usually points to a failed cat, post cat sensor usually provides little variance, constant 0.5v if everything is good.
|
|
IP Logged |
Rally Drivers Do It Sideways
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #9 on: Dec 8th, 2008, 5:28pm » |
Quote Modify
|
on Dec 8th, 2008, 5:02pm, martin_rowe wrote:Unfortunatly Llambda value of 1.01 - 1.03 means emissions are correct, (Llambda value will not change if the cat is good or bad) with that Llambda reading, but still high CO means the cats are not 'burning' off the CO and HC's, they only rattle when the 'brick' breaks up, how long have you owned the car ?, the catsare expensive, many people remove the 'brick'. sorry, with out further data looks like a cat problem, try comparing Llambda sensor readings (electrical) of pre & post cat sensors, a post cat sensor with a fluctuating reading (between 0.2 -0.8v) usually points to a failed cat, post cat sensor usually provides little variance, constant 0.5v if everything is good. |
| Car has been with me since 3 months. Luckily, I found a place in Germany that sells the pair for about 400 euro delivered (175€/pc.+sh). But I'll run through the Forte anyway and have the ODB test, and then see.
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://img.photobucket.com/albums/v521/scorpio_man/scotland_royal_banner_fl_md_clr.gif)
Ford Kuga awd
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 5654
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #10 on: Dec 8th, 2008, 6:28pm » |
Quote Modify
|
on Dec 8th, 2008, 5:28pm, tlundkvi wrote: Car has been with me since 3 months. Luckily, I found a place in Germany that sells the pair for about 400 euro delivered (175€/pc.+sh). But I'll run through the Forte anyway and have the ODB test, and then see. |
| hi there you can get patterned cats from http://www.cats-direct-shop.co.uk/ for about 170 euros + VAT + delivery. *WARNING* they're not the best fit. you may need to 'help' them to fit, but cheaper than you've been quoted. hth andrew
|
|
IP Logged |
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #11 on: Dec 8th, 2008, 6:54pm » |
Quote Modify
|
on Dec 8th, 2008, 6:28pm, scorpio_man wrote: hi there you can get patterned cats from http://www.cats-direct-shop.co.uk/ for about 170 euros + VAT + delivery. *WARNING* they're not the best fit. you may need to 'help' them to fit, but cheaper than you've been quoted. hth andrew |
| http://www.cats-direct-shop.co.uk/two-year-catalytic-converter.php?recor dID=633 http://www.cats-direct-shop.co.uk/two-year-catalytic-converter.php?recor dID=632 Seems ceramic direct fit is about the same price (thanks for the tip!), is there a substantial difference in quality between ceramic and steel cats? Need still to check shipping to Finland. Update: Seems my local discount part dealer sells a universal model for only 99 euros (VAT incl.) pipe diameter 51-57mm, weldable. It says max 2.5 litre engines, but doesn't the cats in the 24V count for 1.45 litres a piece, since each block has one? Will the diameter of the original pipes be within the range?
|
|
IP Logged |
|
|
|
martin_rowe
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/homer.gif) I love YaBB 1G - SP1!
Posts: 879
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #12 on: Dec 9th, 2008, 8:56am » |
Quote Modify
|
I looked at universal cats some time back, you could 'weld' in 2 at the side of the g/box, but bit of a compromise on ground clearance, though you can get the exact same cat that is used as a weld in unit, just has no pipe or flange on it, you could do it that way, just a lot of time & a welder needed.
|
|
IP Logged |
Rally Drivers Do It Sideways
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #13 on: Dec 10th, 2008, 12:23pm » |
Quote Modify
|
Problem seems to have been identified. A T-connector for the vacuum hose had broken off. Irritating enouch, but very, very hard to reach without taking the bullhorn out (sorry, I'm not native English nor a mechanic to say what the part is called). Are all connectors in the joint inner diameter 6 mm? Thanks for all the help!
|
|
IP Logged |
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #14 on: Dec 11th, 2008, 5:03pm » |
Quote Modify
|
on Dec 10th, 2008, 12:23pm, tlundkvi wrote:Problem seems to have been identified. A T-connector for the vacuum hose had broken off. |
| Or then not. Runs slightly uneven on low revs, cables are checked and plugs run 2000km. probably a cat problem then.
|
|
IP Logged |
|
|
|
martin_rowe
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/homer.gif) I love YaBB 1G - SP1!
Posts: 879
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #15 on: Dec 11th, 2008, 5:12pm » |
Quote Modify
|
yes the 'T' under the inlet manifold is very problematic, you can extend the pipes to outside the manifold & make up a 'T' that works ok, another place to check is the EGR system, they come loose causing erratic idle. a squirt round with 'cold start' or wd40 would find it, or a propper 4 gas emission test would show high oxygen, Llambda sensors would try to compensate. fuel trims would also indicate problem.
|
|
IP Logged |
Rally Drivers Do It Sideways
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #16 on: Dec 12th, 2008, 5:12pm » |
Quote Modify
|
Hi, Martin was right from the start. The right cat is dead, the left one almost dead. Lamda sensors were all in order, switching quick. Same for the MAF. The heat sensor in the injection system was dead and replaced, but the effect of this is minimal compared to dead cats (except for that the lambda value in emissions test improved to 1.00-1.01.
|
|
IP Logged |
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #17 on: Dec 12th, 2008, 6:52pm » |
Quote Modify
|
on Dec 11th, 2008, 5:12pm, martin_rowe wrote:... or a propper 4 gas emission test would show high oxygen, Llambda sensors would try to compensate. fuel trims would also indicate problem. |
| The HC didn't go down on idle to less than 160ppm. Oxygen at 0.8, CO at 0.7%. CO2 at best 14.1. On revs the HC went down to 20ppm, but CO remained at 0.7. But that'll go away with new cats. In Finland the limits are (idle/2500rpm) HC 100/100, CO 0.5/0.3, O2 5.0/5.0.
|
|
IP Logged |
|
|
|
tlundkvi
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) Ex. Scorpio 2.9 24V -95
Posts: 909
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Lambda sensors
« Reply #18 on: Dec 15th, 2008, 7:30pm » |
Quote Modify
|
New cats ordered. The pound is low compared to the euro right now, now UK is the place to buy car parts. £152 + 40 P&P to Finland including VAT (both cats, ready-to-fit). In Finland its not possible to get ready-to-fit cats for the scorpio for a reasonable price (e.g. Mondeo cats are here around 300 euros a piece from others than the main dealer, a piece, it seems I saved big time).
|
|
IP Logged |
|
|
|
|