Author |
Topic: heater matrix cold water on return pipe (Read 460 times) |
|
g.wass
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/iceskatekid.gif) What after Scorpio?
Posts: 77
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
heater matrix cold water on return pipe
« on: Nov 18th, 2004, 5:57pm » |
Quote Modify
|
95 2.9 12v Ultima. Heater is luke warm air. Have flushed heater Matrix. Fitted new stat and still warm air. The pipe going into the heater is red hot the return pipe is cold to luke warm. Tried bleeding the system but still the same. Is this a Ultima problem. My 1990 Scorpio I could get it tropical inside and never had problems with it. Is there something I am missing bleeding the system. This is not a reset problem as there is no valve in the hot water circuit , or is there
|
|
IP Logged |
|
|
|
Eddie
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://Homepage.ntlworld.com/eddie.richardson/bizarhoofd.gif)
Must try a different shampoo!
Posts: 495
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater matrix cold water on return pipe
« Reply #1 on: Nov 19th, 2004, 6:02am » |
Quote Modify
|
It would seem the matrix is seriously clogged up. Try disconnecting the feed pipes (at the engine end ,much easier!) and REVERSE flushing. Thats passenger side of car to drivers side. Failing that,drain the matrix,block the inlet pipe and pour some rad cleaner into other end followed by hot water,and leave over night etc. Is there a curry sort of smell in the car ?? If so then the matrix is leaking. Other than this then its a new matrix,about £25 from a motor factor-same as a sierra/granada matrix. A pig to change unfortunately. See article on this site. eddie
|
|
IP Logged |
|
|
|
David_South_West
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://mysite.wanadoo-members.co.uk/davidhelpme/images/0-picture.jpg)
24V............ .Goodness
Posts: 188
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater matrix cold water on return pipe
« Reply #2 on: Nov 19th, 2004, 10:46am » |
Quote Modify
|
If you remove pipes from matrix(drivers side engine bulk head) do not wiggle pipes as the fittings are plastic and easily broken.
|
|
IP Logged |
|
|
|
g.wass
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/iceskatekid.gif) What after Scorpio?
Posts: 77
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater matrix cold water on return pipe
« Reply #3 on: Nov 19th, 2004, 5:42pm » |
Quote Modify
|
Hi thanks for advice but if matrix is leaking would I not see a drop in coolant also would it leak into car. I did notice a curry smell when I first bought the car about 5 months back but put it down to the ethnic origin of the Guy I bought it off
|
|
IP Logged |
|
|
|
Snoopy
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/angryboy.gif) Very old.BAD tempered and missing friends.
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 6278
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater matrix cold water on return pipe
« Reply #4 on: Nov 19th, 2004, 6:55pm » |
Quote Modify
|
If it is just weeping a little and thats all it takes to get that smell you might not even see the offending minute amount of coolant..It evaporates on the HOT surface of the pipe and therefore nevers gets around to drip size.... Once smelt it is a smell you never forget...
|
|
IP Logged |
HELP the FORUM.Please DONATE
|
|
|
|