Author |
Topic: Error codes (Read 324 times) |
|
Octavian_P
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://i35.photobucket.com/albums/d190/Octavian_P/Avatare/Movie1.gif)
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 1126
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Error codes
« on: Jul 14th, 2005, 9:09am » |
Quote Modify
|
Hi there, I have posted this also at OBD advice but there was no answer so i'll give it another go here. I have done an OBD test finally on my scorp and foud out the folowing C1095 = ABS Hydraulic Pump Motor Circuit Failure B1676 = Battery Pack Voltage Out Of Range P0171= System Too Lean - Bank No. 1 So anybody can give me further guidings on what the problems could be. I mention that my ABS light is always on. An i have a delay in acceleation. The TPS test range was betwen aprox 16.5 to 80.5. I have checked the oxigen sensors and they are ok, cats seem to be a bit tired. On the ABS i have cleand the multi plug several times and seems to be ok, sensors are checked also, they all have similar resistance about 1.1 Kohms. Cheers
|
|
IP Logged |
2.0 16V Ultima|2.3 16V Ghia|2.9 24V Cosworth Ghia
|
|
|
Snoopy
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/angryboy.gif) Very old.BAD tempered and missing friends.
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 6278
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Error codes
« Reply #1 on: Jul 14th, 2005, 9:30am » |
Quote Modify
|
Which Plug are you cleaning? the ones to clean are the two 2 pin ones under the front wings! Also check the sensor rings and make sure that they have no metal bits stuck to them. I clean mine out maybe once a year with a low pressure hose pipe and a small plastic probe Also try cleaning the thottle bodies and check for air leaks with regards the throttle delay. .
|
|
IP Logged |
HELP the FORUM.Please DONATE
|
|
|
Octavian_P
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://i35.photobucket.com/albums/d190/Octavian_P/Avatare/Movie1.gif)
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 1126
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Error codes
« Reply #2 on: Jul 14th, 2005, 9:43am » |
Quote Modify
|
I have cleand each sensors plug, i have cleand the multiplug from the modulator/ pump, i have cleaned the small connector wich enters in the abs pump body, Front sensor rings are clean. As for the throttle body....well let's say it's clean now, also the MAF, new air filter....Haven't found an air leak (except broken egr control pipe) till now, is there "a specific" place were to look at, or just generaly check the hoses. PS how big is the EGR presure in the command hose because i think i don't have one at all.
|
|
IP Logged |
2.0 16V Ultima|2.3 16V Ghia|2.9 24V Cosworth Ghia
|
|
|
|