Author |
Topic: Remote Locking (Read 569 times) |
|
Bulldozer
Newbie
I'm a YaBB newbie!
Posts: 8
|
 |
Remote Locking
« on: Sep 14th, 2005, 10:10pm » |
 Quote  Modify
|
Hi all. I hope I'm doing this right? Please advise me if I'm not.
I've only been a member a few days and had my '96 Cossie for just over a week. This site's as good as the car. Thank you to all involved in the administration etc for your hard work; it's fantastic!!
The buttons on the remote that came with my car seemed a bit "iffy" and as I've spent a long time working in electronics and general IT I thought I'd check the sites recommendations and clean up the contacts, give it new batteries etc.
 It wasn't broke; I shouldn’t have tried to fix it!! 
No matter how many times I try to adjust to spring clip connection or re-position the batteries and go and sit in the car to try and re-program it, I can't get it to function.
I think it must be permanently broken; that might be an understatement!
 So now I'm looking for help and advice.
Is there anything else I can do to test whether it is BER (beyond economical repair)??
If I need a replacement, do I have to get one with exactly the same numbers on the back??
Does anyone have one that I don't have to take a mortgage out to buy?
Thanks in advance.
|
|
 IP Logged |
|
|
|
mr._floppy
Junior Member
Posts: 100
|
 |
Re: Remote Locking
« Reply #1 on: Sep 14th, 2005, 10:26pm » |
Quote Modify
|
Don't give up on the one you've got. To start off with, are the batteries new and have you got 'em in the right way up?
Re-programming the remote is ( meant to be ) very simple, turn the ignition to position 1, press the UNLOCK button ( or is it the LOCK button ? I'll get me coat ! ) either way you should get one acknowledgement chime from the computer, take out the ignition key and try out the remote.
|
|
IP Logged |
|
|
|
Highlander
Moderator
Expert
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
Posts: 8244
|
|
Re: Remote Locking
« Reply #2 on: Sep 15th, 2005, 1:06am » |
Quote Modify
|
I think thats the procedure from the handbook which doesnt work.
Try this
http://www.fordscorpio.co.uk/remote.htm
Are you getting the first chime while programming?
Its basically turning the key to the 1 position 5 times and on the 5th time leaving it there,(this is where it should chime)
press the UNLOCK key on the remote then turn the ignition off
Second chime should confirm programming has worked
its not too clear on the site, I know someone recently read it as turning the key four times.
You need to wait a few seconds between each turn of the key during programming,
I found about 5 seconds worked for me, if its too fast it doesnt work.
Failing that and youve checked the batteries etc see if you can meet up with another member and try theirs.
|
|
IP Logged |
on Oct 17th, 2011, 12:35pm, Simmo wrote:I give up !  Too much for an old boy!  |
|
|
|
|
Mickey_2.9
Full Member
Up and running again ! Love it !
Posts: 156
|
|
Re: Remote Locking
« Reply #3 on: Sep 17th, 2005, 4:43pm » |
Quote Modify
|
Since reading this thread I have been trying to get my remotes working but with no luck
I have only had my Scorpio for a few weeks so am still working on it sorting a few things out. It came with 2 remotes, 1 now has new batterys and the batterys in the other are good. I have been through all the turning on to No 1 position etc but the thing I have noticed is that I am not getting the chime after leaving it on for the 5th time. Has anyone any ideas?
Cheers Mike.
|
|
IP Logged |
|
|
|
Snoopy
Administrator
Very old.BAD tempered and missing friends.
Posts: 6278
|
|
Re: Remote Locking
« Reply #4 on: Sep 17th, 2005, 4:52pm » |
Quote Modify
|
Have you tried the old way as per the handbook?
not as per the site. It works with very early cars and the remotes but you can only programme one that way.
They changed the remotes early 96 or was it late memory problems but one or other should work .
Does the chime work? say when you leave the lights on and open the door.
|
|
IP Logged |
HELP the FORUM.Please DONATE
|
|
|
Mickey_2.9
Full Member
Up and running again ! Love it !
Posts: 156
|
|
Re: Remote Locking
« Reply #5 on: Sep 17th, 2005, 4:57pm » |
Quote Modify
|
No I haven't mate, I can't remember seeing anything in the book about it. I will have another look as that may well be the problem because my Scorp is a 1995
Cheers Snoopy.
|
|
IP Logged |
|
|
|
Mickey_2.9
Full Member
Up and running again ! Love it !
Posts: 156
|
|
Re: Remote Locking
« Reply #6 on: Sep 17th, 2005, 5:06pm » |
Quote Modify
|
Snoopy, your a star Man. It worked a treat. The Mrs thinks the remote boot release is brilliant 
|
|
IP Logged |
|
|
|
jetlag
Newbie
I'm a YaBB newbie!
Posts: 13
|
|
Re: Remote Locking
« Reply #7 on: Sep 17th, 2005, 6:48pm » |
Quote Modify
|
Did all scorpios have remote locking as i have just got a 1995 2.0 16v ultima and there was no remote locking thang with the keys, if it should have one can a replacement be bought and programmed?
Jetlag
|
|
IP Logged |
|
|
|
Oliver
Full Member
1998 24v Cosworth Estate
Posts: 201
|
|
Re: Remote Locking
« Reply #8 on: Sep 17th, 2005, 7:13pm » |
Quote Modify
|
Yes it should have a remote and yes you can still buy them. I think they are about £75 from a dealer but they often appear on ebay as well. Programming is very easy when you get the knack.
|
|
IP Logged |
|
|
|
craig
Guest
|
one HERE if it helps
|
|
IP Logged |
|
|
|
jetlag
Newbie
I'm a YaBB newbie!
Posts: 13
|
|
Re: Remote Locking
« Reply #10 on: Sep 19th, 2005, 8:36pm » |
Quote Modify
|
Cheers for that, i will start bidding straight away.
Jetlag
|
|
IP Logged |
|
|
|
Bulldozer
Newbie
I'm a YaBB newbie!
Posts: 8
|
|
Re: Remote Locking
« Reply #11 on: Sep 20th, 2005, 7:57am » |
Quote Modify
|
 Thanks to everyone who has posted replies, especially Snoopy.
With a little patience with the +ve terminal, some work with silver foil and a decent adhesive (Blue Peter style) and most importantly discarding all the advice from almost everywhere that told me to ignore the re-programming instructions in the handbook because they are wrong.
The instructions in the handbook were right!
Special thanks to Snoopy for that information.
I read so much about NOT doing it the way it describes in the handbook that; I never did.
All is well and I’m relieved that I’ve not destroyed £££’s worth of equipment.
Now for the ABS/TCS lights . . . Anyone got a heads up on this one? I’ll start by trawling the past posts, advice, etc.
Thank again all
|
|
IP Logged |
|
|
|
craig
Guest
|
that could well be a case of the sensors need cleaning,i'll go and have a look for the page on that for you......
here you go,have a read of THIS ,might just help you out
|
|
IP Logged |
|
|
|
|
Home
Help
Search
Members
Login
Reply
Send Topic
Print
Remove