Author |
Topic: Idle Control Valve (Read 3215 times) |
|
Alastair
Full Member
2.3 Ghia X & MGB Roadster
Posts: 129
|
 |
Idle Control Valve
« on: Apr 24th, 2007, 7:06pm » |
 Quote  Modify
|
Hi Guys
S reg 2.3 16 v Auto
Can anybody please tell me where / what the Idle control valve is and what the problems would be if this packed in.
Sunday afternoon - Edinburgh City By-pass - outside lane - 70mph ish. car coughs and cuts out. Friendly AA man can't restart. figures its the fuel pump
(having listened under car and heard it priming but cutting out). Garage checked fuel pump and say this is OK,-fuel and spark present. - say it is the Idle Control Valve. - Help please
Alastair
|
|
 IP Logged |
|
|
|
Spannerdemon
Guest
|
The Idle control Valve sits on the inlet manifold at the front of your engine. It monitors the minute amount of air entering the throttle body when the throttle butterfly valves are closed, to ensure that the engine will not cut out when idling at say traffic lights. There is a tamper proof screw on the inlet manifold. DO NOT mess with this.
These cars are all approx 10 years old. The valves fail. New one, or a thorough clean is the usual way. They need a new gasket. If you check Ebay, they come up quite often, and I have it on good authority from a guy at Ford, that many of them are the same.
The one on my car at the moment is actually listed for a Ford Ka,  but it works 100%.
If you look half way down this post from the Granada and Scorp site, you'll get a good idea of what's involved.
HERE
ALSO.....Not sure if your car has a MAF, perhaps someone could advise you, as I know that these can cause probs when dirty. The 12v (like mine) doesn't have a MAF.
Hope this helps you. 
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
Ford Kuga awd
Posts: 5654
|
|
Re: Idle Control Valve
« Reply #2 on: Apr 24th, 2007, 8:53pm » |
Quote Modify
|
hi there
can we have a bit more info. 
aa can't re-start it, or it starts, but won't run?
if it starts, will it run with a bit of throttle?
with it cutting out at speed, i'd say it was electrical.
try swapping the heated windscreen relay with the ignition one.
relays
hth
btw, i'd have a look (obd-2 scan) at it, if you can get it through to glasgow. we normally meet at the end of the M74. see the meetings section.
|
|
IP Logged |
|
|
|
Jonnycab
Senior Member
Former owner of 2.3 Ultima Facelift saloon
Posts: 3900
|
|
Re: Idle Control Valve
« Reply #3 on: Apr 25th, 2007, 1:57am » |
Quote Modify
|
Wouldn't be a fault with the fuel cut off switch would it ?.....
......If the fuel pump is working fine, then that's the only reason I can think of why a car would suddenly cut out at 70mph
Regarding the car not being able to restart, then I would plump towards the fuel pressure regulator rather than the idle control valve
|
|
IP Logged |
|
|
|
Alastair
Full Member
2.3 Ghia X & MGB Roadster
Posts: 129
|
|
Re: Idle Control Valve
« Reply #4 on: Apr 25th, 2007, 8:03am » |
Quote Modify
|
Thanks Guys - I will check out all these helpful tips
Scorpio-man
It will start every 3rd or 4th attempt for a second or so. won't catch and run on throttle.
I will let you know
Alastair
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
Ford Kuga awd
Posts: 5654
|
|
Re: Idle Control Valve
« Reply #5 on: Apr 25th, 2007, 11:16am » |
Quote Modify
|
hi there
i'd forget about the idle control valve for the moment. sounds more like fueling, be it the pump, fuel pressure regulator, fuel filter.
these are the things to check first.
also check the spark plugs. if fuel is getting to the injectors, then they will be wet with all this non starting.
hth
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
Ford Kuga awd
Posts: 5654
|
|
Re: Idle Control Valve
« Reply #6 on: Apr 25th, 2007, 12:27pm » |
Quote Modify
|
hi there
i've moved this to the problem section to see if we get more ideas.
you don't have a battery issue? flicking neddles?
|
|
IP Logged |
|
|
|
Spannerdemon
Guest
|
Try removing relay 17, which is the fuel injection pump relay.
Give it a good solid tap, and re-fit it. Then re-start your engine. These fuel injection relays are a swine to diagnose as they work intermittantly, and then the contacts stick, causing complete engine shutdown. When the contacts cool again, they unstick, and off you go again.
Tip that an auto electrician gave me years ago was to 'very carefully' remove the relay cover (the 'box' part), and look at the mini circuit board inside. If there is any sign of brown marks on it, the relay is almost certainly past its best. You can also see the contacts for any signs of pitting which is what happens when they stick and get overheated.
I agree with the others, I don't think the AA man was right here. I only gave you info about the Idle Valve because that's what you asked for in your post.
I too think this sounds more like an intermittant fuelling problem.
I had this years ago on a Vauxhall Carlton 2.0i. Every so often, driving along without a care in the world, the engine would just stop. No warning. No nothing. Just stop. Stone dead.
VERY dangerous if you were in moving traffic. It was causing me grave concern as it was a significant safety issue for my family.
I'd almost flatten the battery trying to start it again.
Then, some hours later you could go out, and it would start as though nothing had happened.
Took 6 Months, four garages, including a Main Dealer, and countless further incidents to diagnose. I eventually found it quite by chance by doing what I've suggested to you above. When I went to buy a new relay, that's when the auto-electrician gave me the info about the old one. He took the top off the old one, and sure enough, it was all brown, and a dead giveaway.
May work.....let's hope.
|
|
IP Logged |
|
|
|
Jonnycab
Senior Member
Former owner of 2.3 Ultima Facelift saloon
Posts: 3900
|
|
Re: Idle Control Valve
« Reply #8 on: Apr 27th, 2007, 1:59am » |
Quote Modify
|
Have you tried replacing the fuel pump relay yet, as Spanners suggested ?
The reason I ask is because the same exact thing happened to me tonught 
Just driving along at 30mph, when all of a sudden the car just dies.....the engine just cut out & would not restart after many attempts 
I still had electrics & being as I had recently checked/cleaned the plugs, coils, leads, fuel pressure regulator, injectors, idle control valve etc because of a recent problem, my only thought was the fuel pump or fuel cut off switch.
Then I remembered reading Spanners post about the relay. I have a few spare relays in the boot & as luck would have it, one of them was the fuel pump relay 
I stuck it in & she fired up straight away......& has been fine all night....phew
Spanners....if you hadn't mentioned about the fuel pump relay, then I probably would never have thought to change it....I would probably have been there pulling fuses out until the AA arrived & towed me home, & I would have missed an evenings work....& possibly a mortgage payment 
So Spanners....I owe you a big drink mate......but then again, as you already owe me a big drink..... I guess that makes us quits
|
|
IP Logged |
|
|
|
Spannerdemon
Guest
|
No worries buddy. Glad you're running again. I'll pick up my BAFTA... (Beer at Four in the Afternoon)... later !!
I remember not long after I got my Scorp, that it was YOU who diagnosed my ECU problems after torrential rain went down the loom behind the battery onto the ECU pins. It was running like a sick pig. 
That's what I've always said about this site. Shared information between us owners of the cars, is the best of any car site on the web.
I've sent you a PM.
|
|
IP Logged |
|
|
|
Alastair
Full Member
2.3 Ghia X & MGB Roadster
Posts: 129
|
|
Re: Idle Control Valve
« Reply #10 on: May 2nd, 2007, 6:04pm » |
Quote Modify
|
Update - Car has been in the garage since I started this post on 24 April. I weas advised at the time that the problem was the idle copntrol valve. (this is a ford dealer in Edinburgh). I passed on a copy of all your responses but they were adamant and fitted a new valve. Since then they have had the car running and serviced it.
I was on my way to pick it up lat Thursday when they phoned to say it had cut out on the test run and they could not restart it.
From then till now they have been testing everything thay could think of and i have had reports that every single diagnostic check is reading ok. ??
NOW the bit where I urgently need your help. THey have phoned today to say that it could be the ECU (but they are not sure) and that they cost £700 they also now say that the exhaust is blocked and needs replacec (cat I presume)
Could the car have been running perfectly up to till it cut out if these were thr=e problems and would all the diagnostics carried out not highlight a problem with the ECU. I love the car but £ 1000 makes it a difficult decision.
Help please
Alastair
|
|
IP Logged |
|
|
|
TiberiuS
Senior Member
Ex. 1996 2.3 Ultima - RIP P789 KHJ
Posts: 2257
|
|
Re: Idle Control Valve
« Reply #11 on: May 2nd, 2007, 6:44pm » |
Quote Modify
|
No no no no . I've never had a bad cat so don't know how it'd feel but making the car die at high speed sounds a bit unlikely to me. If it's the ECU, get yourself a known good one from someone on here who's stripping a 2.3 down for parts.
IMO main dealers aren't the best people for servicing/troubleshooting, I had a problem a couple of years back with my car not wanting to start hot, they had it in twice and reckoned they couldn't find a thing wrong and it could be this or that, in the end I did it myself. Ask the dealer whether they've carried out a fuel pressure check. Also, might be a long shot but have you tried a new fuel pump relay?
Regards, Bruce .
|
|
IP Logged |
Bruce - '07 Jaguar XKR coupe, '95 Jaguar XJ Sport 4.0, '82 Ford Capri 2.0 Ghia, '15 Honda Civic (sloooooww..)
|
|
|
tintin
Full Member
I'm a YaBB newbie!
Posts: 592
|
|
Re: Idle Control Valve
« Reply #12 on: May 2nd, 2007, 6:55pm » |
Quote Modify
|
hmmm, sounds a bit dodge to me, i would ask them to fit the old IACV back on the car, and ask to take it away free of charge, as so far they have diagnosed nothing, and are just guessing.....(at your expense !)
my blocked cat produced a flat spot when trying to accelerate hard, but never stopped it from starting !
you can pick up a spare ecu for much less than that from someone on this site (i would reckon on £50), easy enough for you to do yourself (i know, i have two left hands and managed it). you should also check the PATS light to see if its flashing any codes. sounds electric to me, rather than mechanical, if sometimes it starts and runs fine, sometimes does nothing. PATS may be disabling the car, ECU may be broken. was it raining at the time?
ps there are a few of us in edinburgh that can lend a hand, if you can pry it out of the dealers hands. Highlander is very handy, and has plenty of spares. helped me get my baby back on the road with minimum cost......and a friendly smile.
|
|
IP Logged |
'95 Cosworth Ultima
|
|
|
Highlander
Moderator
Expert
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
Posts: 8244
|
|
Re: Idle Control Valve
« Reply #13 on: May 2nd, 2007, 7:08pm » |
Quote Modify
|
Yep i have a crate of 2.3 bits somewhere
|
|
IP Logged |
on Oct 17th, 2011, 12:35pm, Simmo wrote:I give up !  Too much for an old boy! |
|
|
|
|
Spannerdemon
Guest
|
Quote:| COULD be the ECU....COULD be the CAT |
|
They're fishing my friend.....they're fishing. They don't KNOW...Not a good sign at all.
Go back to my post, and you'll see that I too had my car at the Main Dealers for them to fix it.
First revelation was that "Sorry Sir, but we don't have the equipment to fit your under bonnet Diagnostic Plug, but even if we did, it doesn't test the fuel system" !!
Comment by me....along the lines of..."What fonking use is it then" !
Anyway to cut a long story short. they replaced leads, plugs etc etc etc, and took me and it for a test drive, proclaiming it to be running perfectly........and yes, it broke down within five minutes of leaving their workshops with the very same fault......Sound familiar!!!!
I join with the others.......Get it back from this garage ASAP. It sounds as though they are baffled, and just pulling ideas out of a hat. Waste of space I think. I agree with Tinitn, they haven't actually sorted it out so make a stand and refuse to pay for the work.
I ended up threatening my Vauxhall dealer with court after they insisted on charging for work done, but they backed down when I said that they hadn't fixed the fault, and that THAT was why I'd taken the car to them.
Highlander is your best bet. He'll sort you out I'm sure!! But DO try the Relay.
|
|
IP Logged |
|
|
|
scorpio_man
Administrator
Ford Kuga awd
Posts: 5654
|
|
Re: Idle Control Valve
« Reply #15 on: May 3rd, 2007, 8:37am » |
Quote Modify
|
hi there
have a look at the 2 rubber pipes that come out of the exhaust manifold and go to the transducer on the r/h inner wing. have they blown off? if so, then yes the exhaust is blocked.
a new (patterned) cat is about £100 + delivery and can be fitted for about £30-£50. no need to replace exhaust usually.
i'd get your car back BEFORE they do some damage to it!
|
|
IP Logged |
|
|
|
Highlander
Moderator
Expert
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
Posts: 8244
|
|
Re: Idle Control Valve
« Reply #16 on: May 4th, 2007, 8:56pm » |
Quote Modify
|
Ok, Alastair and I have just met up and had a look at it.
It appears to be a wiring/multiplug fault at the EDIS module (its screwed onto the inner wing directly under the coolant tank, you can see it down between the coolant reservoir and the windscreen washer reservoir)
The car started and by moving the wiring at the EDIS multiplug very slightly we managed to have the car running perfectly, running roughly and managed to stall it completely.
I have a multiplug on a 2.0 Estate which i'm fairly sure will be the same as the 2.3
The plan is to cut off the old multiplug off and replace it with the spare one.
I did try another EDIS module which i know to be working but moving the wiring gave the same results.
Here's hoping but i'm fairly confident thats the problem
|
|
IP Logged |
on Oct 17th, 2011, 12:35pm, Simmo wrote:| I give up ! Too much for an old boy! |
|
|
|
|
scorpio_man
Administrator
Ford Kuga awd
Posts: 5654
|
|
Re: Idle Control Valve
« Reply #17 on: May 4th, 2007, 9:04pm » |
Quote Modify
|
good work stuart.
great work from the main dealer as well! 
|
|
IP Logged |
|
|
|
Highlander
Moderator
Expert
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
Posts: 8244
|
|
Re: Idle Control Valve
« Reply #18 on: May 6th, 2007, 2:55pm » |
Quote Modify
|
EDIS multiplug replaced, car started first time and runs perfect!
Problem solved
|
|
IP Logged |
on Oct 17th, 2011, 12:35pm, Simmo wrote:| I give up ! Too much for an old boy! |
|
|
|
|
Alastair
Full Member
2.3 Ghia X & MGB Roadster
Posts: 129
|
|
Re: Idle Control Valve
« Reply #19 on: May 6th, 2007, 5:43pm » |
Quote Modify
|
Many thanks to all who responded and especially to Stuart whom gave up his time on a Friday evening and a Sunday afternoon of what is a holiday weekend.
As Stuart says the car is running and starting as it should and idles rock steady at 850 rpm.
In response to all concerned over the carage charges and advice given - i can advise that on Friday, before I had contacted Stuart, the garage had advised (unprompted) that there would be no charge for any of the diagnostic work (2 days worth) nor for the new idle control valve that they fitted. In fact there would be no charge at all except for the service. This I think is more than fair.
Anyway, touch wood, the car as of now seems better than ever.
Thanks again to all
Alastair
|
|
IP Logged |
|
|
|
|
Home
Help
Search
Members
Login
Reply
Send Topic
Print
Remove