Author |
Topic: heater blows cold air only?? (Read 1498 times) |
|
lucydog
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 65
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
heater blows cold air only??
« on: Feb 2nd, 2008, 5:16pm » |
Quote Modify
|
hi, today my scorpio would not blow any heat from the heater it only blows cold air? (not to good on a cold day like today). the coolant level is the same and coolant is getting hot as normal?.. any ideas??
|
|
IP Logged |
|
|
|
Scorpio_Mike
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/tigger.gif) Jeep Grand Cherokee 3.0 V6 & 2.8 Sierra XR4i 4x4
Posts: 2354
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater blows cold air only??
« Reply #1 on: Feb 2nd, 2008, 6:03pm » |
Quote Modify
|
Sounds like the 'ol blocked heater matrix' problem - try flushing it through. This may give you a bit of warmth but usually the only long term fix is to replace the matrix...or trade the car in like I did when this happened on my '93 Granada Scorpio. There are quite a few articles / threads on this site all about heater matrix problems and replacement.
|
|
IP Logged |
Star sign is Scorpio ! Sierra XR4i's are great...especially when fitted with 4WD
|
|
|
the_machine
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 121
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater blows cold air only??
« Reply #2 on: Feb 2nd, 2008, 6:20pm » |
Quote Modify
|
the valve actuator could have stuck or as Mike says the matrix is blocked. I was successfull in flushing mine and that was 3 months ago. Its still working. I used caustic soda.
|
|
IP Logged |
|
|
|
Snoopy
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/angryboy.gif) Very old.BAD tempered and missing friends.
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 6278
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater blows cold air only??
« Reply #3 on: Feb 2nd, 2008, 7:01pm » |
Quote Modify
|
Before you do any of that .. a couple of questions ... Do you have Climate control or just A/C If you have CC then do a reset if you had hot air before then that should fix it... If not then most likely scenario is a blocked matrix.
|
|
IP Logged |
HELP the FORUM.Please DONATE
|
|
|
Jonnycab
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](http://i70.photobucket.com/albums/i101/jonnycab/JP_nitrous.gif)
Former owner of 2.3 Ultima Facelift saloon
Posts: 3900
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater blows cold air only??
« Reply #4 on: Feb 3rd, 2008, 3:07am » |
Quote Modify
|
Check both the matrix inlet & outlet matrix pipes. They should be the same heat & too hot to hold when engine has warmed up. If the inlet pipe is hot, but the outlet pipe is cold, then you have a blocked or restricted heater matrix The matrix can be flushed with a hose, but in my experience this was only a temporary fix.....I replaced the matrix in the end But I've recently read that phosphoric acid may be the solution, as it breaks down hard water deposits (limescale). Where can you buy phosphoric acid ?.......at any shop, in a can of Coke/Pepsi. Cola drinks contain phosphoric acid.......god knows what it does to your guts So why not try disconnecting the matrix hoses from the manifold & the engine, pour coke into the inlet hose until the matrix is full & it's coming out of the outlet hose, then plug both hoses & leave it over night I've never tried this method of un-blocking a heater matrix, but if someone would like to try it & then post the results, then it would be interesting to see what happened
|
|
IP Logged |
|
|
|
ren
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) 95 N 2.9 24v Cossie Estate
Posts: 480
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater blows cold air only??
« Reply #5 on: Feb 4th, 2008, 11:43pm » |
Quote Modify
|
i had my matrix changed last week and the garage gave me my old one back,on looking at it i think the reason backflushing does not work is because the pipe is not continuouse as say a heating element were you have a start and finish, there are 7 ubend pipes in the matrix and they connect to the inlet and outlet as individual connections there are 7 holes along the inlet and 7 holes along the outlet so pressure of water will clear 1 maybe 2 but not the 7 pipes need something that can be directed into each hole down the inlet tube to clear each pipe 1 by 1
|
|
IP Logged |
|
|
|
harry.m1byt
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) What's YaBB?
Posts: 792
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: heater blows cold air only??
« Reply #6 on: Feb 10th, 2008, 6:45pm » |
Quote Modify
|
on Feb 4th, 2008, 11:43pm, ren wrote:there are 7 ubend pipes in the matrix and they connect to the inlet and outlet as individual connections there are 7 holes along the inlet and 7 holes along the outlet so pressure of water will clear 1 maybe 2 but not the 7 pipes need something that can be directed into each hole down the inlet tube to clear each pipe 1 by 1 |
| That has been said before - that there is basically a sort of manifold at each end. My guess would be that the tubes through which the coolant passes through with least velocity, are the ones which block up first. Once the blockages start, complete pipe blockage is not too far away. Just a thought on this.... I wonder if the RTL cleaning fluid, as used by commercial a/c engineers for cleaning the alloy cooling fins of a/c units might also work to clean out a matrix?
|
|
IP Logged |
August '95 2.9 12v auto Ultima - Now flashing
|
|
|
|