Author |
Topic: 2-3 Transit inlet manifold? (Read 1193 times) |
|
ro284
Full Member
I'm a YaBB newbie!
Posts: 508
|
|
2-3 Transit inlet manifold?
« on: Jan 3rd, 2012, 10:08pm » |
Quote Modify
|
2-3 Transit inlet manifold? Can anyone tell me if this is the same as the Scorpio 2-3 manifold please? After overheating last year and getting oil in the coolant, which must have become acidic, the stat housing seems very thin! i have repaired it but think i had best replace this if i get the car through, m.o.t! plus re m.o.t. is the flashing air bag light a fail yet? cheers Bob
|
|
IP Logged |
Bob Dorset
|
|
|
leewar
Senior Member
I'm a YaBB newbie!
Posts: 1504
|
|
Re: 2-3 Transit inlet manifold?
« Reply #1 on: Jan 4th, 2012, 12:43am » |
Quote Modify
|
Air bag light not a fail yet. Understand it could be by April.
|
|
IP Logged |
|
|
|
Tompion
Administrator
1997 2.3 Ultima estate.
Posts: 2918
|
|
Re: 2-3 Transit inlet manifold?
« Reply #2 on: Jan 4th, 2012, 3:15am » |
Quote Modify
|
Yes a 2.3 Transit manifold will fit (assuming there isn't more than 1 type of 2.3 engine used in transits). There was someone selling new transit ones on Ebay a while back & several people here used them on Scorpio's. Some of the bolt on bits are slightly different – throttle body, idle air control valve & I think one of the temp sensors so you’ll have to swap them from the Scorpio manifold. The stat housing gets eaten away by the coolant/heat anyway so probably nothing to do with the oil. The asbestos looking lining in this picture is actually the plastic eaten into: If the steel insert is rusty like this one it's a good idea to push it out, clean it up & treat it for rust before it swells and cracks the manifold like this one has.
|
|
IP Logged |
ABS multiplug wheel sensor pins MK IV or MK 20
|
|
|
lesterlad aka Rodders
Full Member
2.3 Ghia x Estate (Manual)
Posts: 877
|
|
Re: 2-3 Transit inlet manifold?
« Reply #3 on: Jan 4th, 2012, 9:20am » |
Quote Modify
|
on Jan 4th, 2012, 12:43am, lleewar wrote:Air bag light not a fail yet. Understand it could be by April. |
| I understood it came in on the 1st Jan this year.
|
|
IP Logged |
There's are methods to my madness!!! I'm not sure what the methods are but there's definitely madness in them
|
|
|
Jonnycab
Senior Member
Former owner of 2.3 Ultima Facelift saloon
Posts: 3900
|
|
Re: 2-3 Transit inlet manifold?
« Reply #4 on: Jan 5th, 2012, 3:53am » |
Quote Modify
|
As Tompion confirms, it is the same manifold .....I bought one of those new manifolds off Ebay a couple of years back (£50 if I remember right) & it was exactly the same manifold as the 2.3 Scorpio manifold
|
|
IP Logged |
|
|
|
ro284
Full Member
I'm a YaBB newbie!
Posts: 508
|
|
Re: 2-3 Transit inlet manifold?
« Reply #5 on: Jan 5th, 2012, 8:16pm » |
Quote Modify
|
Thanks Tompion, thanks Jonnycab for confirming. Bob
|
|
IP Logged |
Bob Dorset
|
|
|
|