Author |
Topic: Scorpio BOB cosworth no spark (Read 2935 times) |
|
barton
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 4
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Scorpio BOB cosworth no spark
« on: Apr 19th, 2014, 6:49pm » |
Quote Modify
|
Hi, i implemented the 2,9i 24v BOB into Cortina MK4 with all the stuff (engine, gearbox, ECU, PCM, fuel pump .... i would say, i put everything into the Cortina) However i have no spark on spark plugs. The engine wires are new, i have changed the EDIS. No result. Has anyone any idea where i should try to find problem? I consider i have cut some wire from ECU which lead to doors or to rear part of the car, i left the fuel cut off valve wires, and the emergency switch in the rear boot lock. Thanks for help, Boris.
|
|
IP Logged |
|
|
|
Tompion
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://i.imgur.com/YwLOTZk.jpg)
1997 2.3 Ultima estate.
Posts: 2918
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Scorpio BOB cosworth no spark
« Reply #1 on: Apr 19th, 2014, 8:32pm » |
Quote Modify
|
Hi Did you transfer the PATS system, are you using a key (or its transponder) coded to the system within the vicinity of the PATS transceiver, did you include the PATS light & does it flash any codes?
|
|
IP Logged |
ABS multiplug wheel sensor pins MK IV or MK 20
|
|
|
barton
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 4
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Scorpio BOB cosworth no spark
« Reply #2 on: Apr 19th, 2014, 9:23pm » |
Quote Modify
|
Yes, PATS is there, I do have 3 coded keys. The ECCV was checked for errors during ignition. I expect it could be failure of camshaft sensor, but such a failure should not be typical for that engine, and i can not get any spare sensor or since i cut out some wires (seats, doors, abs) there could be missing some ground, or other necessary circuit.
|
|
IP Logged |
|
|
|
Dave2302
Senior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/winnie.gif) 2006 Mercedes S55 AMG, Retired Barefoot Waterskier
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 1119
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Scorpio BOB cosworth no spark
« Reply #3 on: Apr 20th, 2014, 10:50am » |
Quote Modify
|
Check + and - to EDIS module and make sure wiring from EDIS Module to ECU is real good, they seem to need really good wiring or they give all sorts of grief. Also make sure the coil pack has 12V with Ignition on HTH Dave
|
|
IP Logged |
Dave "The 'ol Bear" ex Footer !
|
|
|
barton
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 4
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Scorpio BOB cosworth no spark
« Reply #4 on: Apr 26th, 2014, 6:21pm » |
Quote Modify
|
Thanks Dave, i will check it.
|
|
IP Logged |
|
|
|
barton
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 4
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Scorpio BOB cosworth no spark
« Reply #5 on: May 13th, 2014, 11:22am » |
Quote Modify
|
So, I did the check. Everything was OK. So no progress yet.
|
|
IP Logged |
|
|
|
|