Author |
Topic: Chase the faults..... (Read 611 times) |
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Chase the faults.....
« on: Jul 16th, 2022, 10:04pm » |
Quote Modify
|
Hi, just a little on-going story....... So, clunky noise from front suspension. It's been there since I had it. Changed the front drop links and ARB bushes. Noticed the radiator had bulged at the bottom and leaking, ordered a new one - still waiting after delivery company had lost it! Flushed engine and found cam sensor wiring and oil pressure switch had decayed. Repaired this. While up on stands, I changed the gearbox filter and oil. Tested the car, lost drive, erratic idle etc etc, oh and a flashing o/d light. Wiggle tested wiring and stalled car. Ok, wiring is faulty. Stripped intake off and removed wiring harness from the engine and transmission. Its completely disintegrated. I have made a new harness , well, I have separated the transmission and engine harnesses. Transmission one fitted as of today, I have not routed this back through the Vee. Just finishing engine harness. Fingers crossed it works when all this work is done!!!!! Stay tuned for updates.......and I will post some pics later
|
|
IP Logged |
|
|
|
a900one
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) A scorpio is for life not just for christmas
![Email](https://www.fordscorpio.co.uk/YaBBImages/email.gif)
Posts: 980
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #1 on: Jul 17th, 2022, 11:28am » |
Quote Modify
|
Well done that man I hope your efforts are justly rewarded. ALl the best Gerald.
|
|
IP Logged |
|
|
|
Nunnspoet
Full Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I love YaBB 1G - SP1!
Posts: 798
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #2 on: Jul 18th, 2022, 9:47am » |
Quote Modify
|
Yeah! Well done, please keep us informed. Happy day Mike N
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #4 on: Jul 22nd, 2022, 9:27pm » |
Quote Modify
|
Hi all. I'm happy to report that Scorpy is running again!! A frustrating end to a few weeks. I have got very intimate with the workings of transmissions and sensors! You can buy new pins for the two main engine bay connectors. 37488 - non-insulated male pins from The tool academy. 13 quid for 50 pins. I used 18 gauge wire for injectors and power feeds and 20 gauge for sensors. All crimps run to main connectors for ease. I hand-layed all the white cables and sheathed in DR25. Cables in the vee were covered in heat resistant material. I managed to remove and refit transmission harness without lowering gearbox, a bit of a chore and tested my patience. Repaired the crankcase breather pipes and two airleaks. Sharper pullaway, VIS valve works now, no harsh overdrive changes. If you would like, I can post the wiring info. Dan I have a more detailed pinout test info to hand too.
|
|
IP Logged |
|
|
|
Tompion
Administrator
![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/staradmin.gif)
![](http://i.imgur.com/YwLOTZk.jpg)
1997 2.3 Ultima estate.
Posts: 2918
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #5 on: Jul 24th, 2022, 4:35pm » |
Quote Modify
|
Glad you got it sorted. Some of the sensor pins in the main connectors are gold plated and you're not supposed to mix the two types. Hang onto the old ones, if you find over-time incorrect sensor values you may need to replace them. Also some wires should be twisted pair but how likely interference is if not twisted I haven’t a clue. In my notes on the 2.3 autobox C112 socket, pins 26 & 30 are gold plated, 17 & 20 are twisted pr. Don’t know offhand about the Cosworth. Dave
|
|
IP Logged |
ABS multiplug wheel sensor pins MK IV or MK 20
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #6 on: Jul 24th, 2022, 9:17pm » |
Quote Modify
|
Thanks Tompion. I used screened twisted pairs for cam, crank and speed sensor. It's quite funny with the gold pins etc, with the wire quality being what it is! I'm suprised the car made 25yrs with no issues. No-one at work has seen anything like the wiring condition on this car. I have driven the car today after a wash, polish and leather clean. The gearchanges are very smooth and the throttle response is better. Awesome car - proper motor! I repaired the heater controls today, now the fan motor runs as it should. I have Halfords coming to re-gas the aircon on Tuesday. What's next
|
|
IP Logged |
|
|
|
cobrascim
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 81
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #7 on: Jan 13th, 2023, 6:23pm » |
Quote Modify
|
on Jul 22nd, 2022, 9:27pm, Scorpio_Dan wrote:Hi all. I'm happy to report that Scorpy is running again!! A frustrating end to a few weeks. I have got very intimate with the workings of transmissions and sensors! You can buy new pins for the two main engine bay connectors. 37488 - non-insulated male pins from The tool academy. 13 quid for 50 pins. I used 18 gauge wire for injectors and power feeds and 20 gauge for sensors. All crimps run to main connectors for ease. I hand-layed all the white cables and sheathed in DR25. Cables in the vee were covered in heat resistant material. I managed to remove and refit transmission harness without lowering gearbox, a bit of a chore and tested my patience. Repaired the crankcase breather pipes and two airleaks. Sharper pullaway, VIS valve works now, no harsh overdrive changes. If you would like, I can post the wiring info. Dan I have a more detailed pinout test info to hand too. |
| Hi Dan, Well done in getting yours sorted. I'm about to do the same as you have done with the wiring loom. Thanks for the pin type number I will get those ordered up. I'm a bit luckier in that I have a spare engine with the loom attached that I'm going to strip out to make new/recon one. I'm hoping this will resolve my cutting out issues. John.
|
|
IP Logged |
|
|
|
cobrascim
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 81
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #8 on: Jan 14th, 2023, 11:29am » |
Quote Modify
|
Hi Dan, Did you order new plugs or were you able to salvage and re-use existing ones? Could you post up wiring info if you have it? John.
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #9 on: Jan 14th, 2023, 6:23pm » |
Quote Modify
|
Hi Cobrascim, I managed to save most of the plugs. Some are available online, Burton Power do some, ebay etc. I re-used the main conns but used new pins. I replaced injector and cam/crank connectors. Terminals are available. Some of the terminals are hard to remove without the proper extraction tools. I will dig out my pinout info. I'm in Northamptonshire, are you nearby?
|
|
IP Logged |
|
|
|
cobrascim
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 81
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #10 on: Jan 14th, 2023, 6:38pm » |
Quote Modify
|
on Jan 14th, 2023, 6:23pm, Scorpio_Dan wrote:Hi Cobrascim, I managed to save most of the plugs. Some are available online, Burton Power do some, ebay etc. I re-used the main conns but used new pins. I replaced injector and cam/crank connectors. Terminals are available. Some of the terminals are hard to remove without the proper extraction tools. I will dig out my pinout info. I'm in Northamptonshire, are you nearby? |
| Hi Dan, I'm up in Scotland so not that close which is a shame. I bought a kit with a load of pin removal tools - problem is knowing which to use I think I'll strip the loom off and see which plugs I can get. New loom was priced at around £1600 that's if you can even get one. Thanks for all the info. Makes it a bit less daunting. May try videoing the bits and bobs and see how it comes out. Dunno yet as it all adds time onto the work.
|
|
IP Logged |
|
|
|
cobrascim
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 81
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #11 on: Jan 16th, 2023, 12:54pm » |
Quote Modify
|
Hi Dan, I see your wiring info has disappeared was there an issue with it? Regards. John.
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #12 on: Jan 16th, 2023, 7:35pm » |
Quote Modify
|
No issues as such. I didn't like the way it pasted up! I will try another way...........
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #13 on: Jan 16th, 2023, 7:47pm » |
Quote Modify
|
PIN Wire Colour Destination 2 Black/Blue TRS - pin 4 4 Black VSS 5 Yellow/Green Post Cat LH 8 White/Blue VSS 10 Violet/White TRS - pin 3 13 Violet/Blue TRS - pin 2 14 Grey/Orange Post Cat LH 15 Green/White Post Cat LH 16 Yellow/Blue Post Cat RH 17 Brown/White TSS Twist with pin 36 - pin 3 19 White/Blue Post Cat RH 20 Violet/Grey Post Cat RH 25 White/Red Trans Oil Temp - pin 4 26 Violet/Blue Thu - crimp 1 27 Black/White TRS - pin 6 28 Black/White Solenoid 4 -pin 9 30 Black/Red EPS - pin 12 31 Black/Yellow Solenoid 1 - pin 16 32 Black/Blue Solenoid 2 - pin 14 33 Black/White Lockup Sol - pin 5 36 Violet/White TSS Twist with pin 17 - pin 2 37 Black/Yellow TRS pin 1 38 Black/Orange Solenoid 3 - pin 7
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #14 on: Jan 16th, 2023, 7:50pm » |
Quote Modify
|
Crimp 1 Pin 26 Colour THU pin 1 Violet/Black THU pin 10 Violet/Black THU pin 11 Violet/Black VSS Violet Transmission Range Sensor 1 Black/Yellow 37 2 Violet/Blue 13 3 Violet/White 10 4 Black/Blue 2 5 Not Connected 6 Black/White 27 7 Brown/Yellow Splice Eng 8 Not Connected Position Resistance Pin 6 – 7 P 3.7k – 4.6k R 1.3k – 1.6k N 660R – 807R D 361R – 442R 2 190R – 237R 1 78R – 95R
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #15 on: Jan 16th, 2023, 7:52pm » |
Quote Modify
|
Transmission Connector 1 12v for Lockup Sol 2 Cam Sensor pin 35 3 Cam Sensor pin 17 4 Trans Oil Temp pin 25 5 Lockup Sol Control pin 33 6 Not Connected 7 Solenoid 3 pin 38 8 Spliced to Engine Harness 9 Solenoid 4 pin 28 10 12v for Sol 1,2,3,4 11 12v for EPC Sol 12 Control of EPC pin 30 13 Not Connected 14 Solenoid 2 pin 32 15 Not Connected 16 Solenoid 1 pin 31
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #16 on: Jan 16th, 2023, 7:58pm » |
Quote Modify
|
PIN Wire Colour 3 Black/Red Injector 6 pin 1 4 Black/Yellow Injector 2 pin 1 5 Black/Yellow Idle Valve pin 1 8 White TPS pin 2 10 White/Blue EDIS 12 Black/Green Injector 5 pin 1 14 Violet/White Air charge Temp pin 1 15 White/Red Crank Sensor pin 1 16 White/Green EDIS 19 Black/Green Temp Sensor 20 Brown/Red Crank Sensor pin 2 22 Brown/Yellow EDIS 25 Black/Green Oil Pressure Switch 26 Violet/White Cam Sensor pin 1 27 Brown/Red See Crimp 1 28 Green EDIS + Suppressor 30 Black/Orange Injector 4 pin 1 31 Brown/White Cam Sensor pin 2 32 Yellow TPS pin 1 33 White ECT – Engine Cool pin 1 36 Black/Blue Injector 3 pin 1 37 Black/White Injector 1 pin 1 38 Violet/Blue See Crimp 2 Crimp 1 PIN 27 TPS - Brown Engine Coolant - Brown Air Temp Brown/White Post-Cat(White) - Brown/Blue Post-Cat(Black) - Brown/Green TRS pin7 - Brown/Yellow THU pin8 - Brown/Green Crimp 2 PIN38 Injector 1 pin 2 Injector 2 pin 2 Injector 3 pin 2 Injector 4 pin 2 Injector 5 pin 2 Injector 6 pin 2 Idle Valve Violet/Yellow
|
|
IP Logged |
|
|
|
Scorpio_Dan
Newbie
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 45
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #17 on: Jan 16th, 2023, 8:07pm » |
Quote Modify
|
As I may of stated before. I made the two harnesses seperately and run the engine harness through the Vee as before. The transmission harness has been routed up from the transmission and around the brake master cylinder. The interconnection between the two (transmission solenoid commons) are made with a simple single way connector. I used the pinouts from this site along with my own notes to complete the wiring. I cut the original transmission wiring at the vee and pulled it down. I only removed a lambda sensor and dropped the heatshield to get access to the linkages and wiring connectors, quite a big faff to get done but possible if your patient.
|
|
IP Logged |
|
|
|
cobrascim
Junior Member
![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif) ![*](https://www.fordscorpio.co.uk/YaBBImages/star.gif)
![](https://www.fordscorpio.co.uk/YaBBImages/avatars/blank.gif) I'm a YaBB newbie!
Posts: 81
|
![](https://www.fordscorpio.co.uk/YaBBImages/xx.gif) |
Re: Chase the faults.....
« Reply #18 on: Jan 17th, 2023, 2:03am » |
Quote Modify
|
on Jan 16th, 2023, 8:07pm, Scorpio_Dan wrote:As I may of stated before. I made the two harnesses seperately and run the engine harness through the Vee as before. The transmission harness has been routed up from the transmission and around the brake master cylinder. The interconnection between the two (transmission solenoid commons) are made with a simple single way connector. I used the pinouts from this site along with my own notes to complete the wiring. I cut the original transmission wiring at the vee and pulled it down. I only removed a lambda sensor and dropped the heatshield to get access to the linkages and wiring connectors, quite a big faff to get done but possible if your patient. |
| Fantastic Dan thanks. Lots of great info there. It does look like the best way to do it by re-routing the transmission wiring and I will probably do the same. I will post up how I get along hopefully sooner rather than later. Thanks again. Regards. John.
|
|
IP Logged |
|
|
|
|