|
||
Title: 2.3 Cracked inlet manifold Post by sg_frost on Apr 17th, 2004, 3:02pm :( My inlet manifold is cracked above the thermostat, spraying a jet of water out when i rev it. So i need a inlet manifold. I changed the temp sensor last year and the brass ferule came out of the plastic housing, this was stuck back in with araldite. Do these plastic manifold go brittle with age, or has anyone else had similar problems? It's only a '98 car, but it has got 116 thousand miles on it!!! |
||
Title: Re: 2.3 Cracked inlet manifold Post by scorpio_man on Apr 17th, 2004, 3:14pm hi there copied from the mailing list. Chap told me he was breaking a scorpio-moderate front/rear damage so engine may be ok-I 'think' its a 2.3 auto. Call LUKE on 07810651184. Cardiff area. also from eddie Inlet MANIFOLD has been reassembled WITH new bolt and runs well AND the leak seems to have gone! Annoyingly ford dealer refuse to take back manifold gasket I bought in anticipation,still sealed in bag. Rotters! eddie |
||
Title: Re: 2.3 Cracked inlet manifold Post by sg_frost on Apr 17th, 2004, 3:32pm fantastic, will give it a go. |
||
Title: Re: 2.3 Cracked inlet manifold Post by sg_frost on Apr 17th, 2004, 3:54pm Nope, he had a 2 litre, and sold the whole lot. |
||
Title: Re: 2.3 Cracked inlet manifold Post by sg_frost on Apr 17th, 2004, 8:31pm Is the inlet manifold on the 2.0 litre engine the same as a 2.3? There are lots of the 2 litres around. |
||
Title: Re: 2.3 Cracked inlet manifold Post by tjp_lawson on Apr 17th, 2004, 10:36pm manifold is peculiar to the 2.3 about 200.00 quid complete with relevant gaskets |
||
Title: Re: 2.3 Cracked inlet manifold Post by Eddie on Apr 18th, 2004, 4:55pm Have you positively eyeballed the crack? If not then take a good close look and see if there is a bolt missing below the thermostat housing. eddie |
||
Title: Re: 2.3 Cracked inlet manifold Post by sg_frost on Apr 18th, 2004, 5:55pm Not a bolt loose. Crack about 1 inch long running from thermostat area bacwards, right on top. Reved it and two jets of water washed my face!!!!!!!!!!!! |
||
Title: Re: 2.3 Cracked inlet manifold Post by MATTTT on Apr 19th, 2004, 10:00am id try repairing it with chemical metal i used that stuff to fix a really bad corroded thermostat housing on a old sherpa engine that had been sat around as a non runner and the part isnt available it worked a treat and is still ok 2 yrs later |
||
Title: Re: 2.3 Cracked inlet manifold Post by Eddie on Apr 21st, 2004, 11:36am I think matt is refering to 'JB WELD' its good stuff if used properly. Use fairly coarse emery paper to clean and provide a key surface,then clean the area with something like brake or carb cleaner before application.GIVE IT PLENTY OF TIME TO SET> eddie |
||
Title: Re: 2.3 Cracked inlet manifold Post by sg_frost on Apr 21st, 2004, 8:18pm new one fitted now, £213 including a new temp sensor to replace the one that was stuck in with araldite!!!!!! ;D |
||
Ford Scorpio Forum » Powered by YaBB 1 Gold - SP 1.3.1! YaBB © 2000-2003. All Rights Reserved. |