Ford Scorpio Forum - Print Page


    
      
        Ford Scorpio Forum
        (https://www.fordscorpio.co.uk/cgi-bin/yabb/YaBB.pl)
      

        General >> Parts For Sale >> 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
        
(Message started by: kyanther on Dec 19^th, 2008, 7:42pm)

Title: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by kyanther on Dec 19^th, 2008, 7:42pm

HI
I HAVE FOR SALE A 24V BOB COSSIE WITH ALL ANCILLERIES.
AT PRESENT IT HAS THE FLYWHEEL STILL ATTACHED. IT IS A GOOD ENGINE THAT CAME OUT OF MY ULTIMA WHICH WAS STRIPPED FOR INSTILLATION IN A KIT BUT IS JUST TO DIFFICULT. IT HAS A GOOD AUTOBOX. NEW WATER PUMP HAS DONE 50 MILES AS HAS THE PIPE GOING THROUGH HEAD. I HAVE A NUMBER OF MIDDLE ROCKER GASKETS (O-O-O YOU KNOW WHAT I MEAN) 1 SET OF OUTER GASKETS. INLET AND EXHAUST GASKETS.

THE MANUAL GEARBOX WAS CONVERTED BY A QUALIFIED MECHANIC FROM A 4X4V6 AND A 4POTRWD AND YES THE FIRST MOTION SHAFTS WERE SWAPT OVER.

THERE IS ALSO A GOOD SECOND HAND 2.8 FLYWHEEL AND FULL CLUTCH ASSEMBLY

PROP SHAFT.

THERE IS ALSO A PAIR OF BOA TURBO MANIFOLDS

THE ONLY THING THAT NEEDS ATTENTION IS THE WIRING LOOM THROUGH THE THE V.

I'M LOCATED IN TAMWORTH STAFFORDSHIRE.
AND AM OPEN TO OFFERS

I AM GOING AWAY XMAS EVE TILL JAN 9
07809741632

Title: Re: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by Highlander on Dec 19^th, 2008, 7:59pm

Hi, i'm thinking of doing the manual conversion, whats the bit about the first motion shafts? not heard this before..

Title: Re: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by kyanther on Dec 19^th, 2008, 8:44pm

RIGHT, HOPE I EXPLAIN THIS CORRECTLY:
(IF NOT I'L GET THE MECHANIC THAT DID THE CON TO!!)
THE FIRST SHAFT THE PART THAT GOES INTO THE ENGINE IS DIFFERENT LENGTHS IN THE 4POT AND THE V6. THIS IS OVERCOME BY SWOPPING THIS PART AND THE FRONT CASE OVER. IT IS VERY TIME CONSUMING NOT DIFFICULT BUT THE SPECILIST TOOLS HAD TO BE MADE AT EACH STAGE. SO NOT TO STRESS THE GEARS THE COVERS MUST BE PULLED OFF DONT PUSH THE GEARS THROUGH.
I HOPE THIS MAKES SENSE

Title: Re: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by Highlander on Dec 19^th, 2008, 9:00pm

Ah right got you, input shafts swapped over?

Title: Re: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by Matt on Dec 29^th, 2008, 4:45pm

hey, yep you'll have to use the sierra input shaft for the box, its exactly the same just a bit longer ;D

Title: Re: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by Highlander on Dec 29^th, 2008, 8:22pm

Same but different then :)

Title: Re: 24vBOB ENGINE AUTO AND MANUAL BOX+MORE
Post by pinto on Dec 29^th, 2008, 8:28pm

on 12/29/08 at 20:22:10, Highlander wrote:

Same but different then :)

Ask any woman - its the little bit extra on the end that counts ;D :P

Kyanther, i know you've put offers, but do you have a ballpark figure in mind ?